Guide Rail, Overall Length 640 mm, Overall Width 25 mm, Overall Height 21.8 mm, Rail Material Aluminum, Manufacturer Size 25, Rail Type Profile, System of Measurement Metric, For Use With Alulin Carriages, Operating Temperature - Maximum 140 Degrees F, Operating Temperature - Minimum 32 Degrees F, Mounting Hole Center to Center 60 mm, Mounting Hole Center to Shaft End 28 mm, Channel Material Stainless Steel, Series Alulin, Mounting Hole Size 11 mm, Channel Type Not Applicable

Linear Round Flange Mount Bearing; Inside Diameter 1 1/4 in; Outside Diameter 2 in; Flange Width Not Applicable; Overall Length 2 5/8 in; Flange Diameter 3.125 in; Dynamic Load Capacity 1;570 N; Flange Thickness 0.375 in; Material Resin; Series SWF; Static Load Capacity 2;740 N; Steady State Speed 5 fps; Housing Style Single; System of Measurement Inch; Maximum Operating Temperature 176 Degrees F; Minimum Operating Temperature -4 Degrees F; Flange Shape Round; Finish Anodized

Linear Shaft, System of Measurement Inch, Diameter 3/4 in, Shaft Type One End Tapped Shaft, End Type One End Tapped, Core Type Solid, Overall Length 6 in, Surface Hardness - Minimum 56 HRC, Material Stainless Steel, Finish Stainless Steel Coated, End Thread Size 5/16-18, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 0.749 in, Diameter Tolerance - Maximum 0.75 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable

Linear Shaft, System of Measurement Inch, Diameter 5/8 in, Shaft Type Both Ends Threaded Shaft, End Type Both Ends Threaded, Core Type Solid, Overall Length 13.5 in, Surface Hardness - Minimum 60 HRC, Material Carbon Steel, End Thread Size 3/8-16, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 0.624 in, Diameter Tolerance - Maximum 0.625 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable, End Thread Length 0.47 in

Linear Shaft, System of Measurement Inch, Diameter 3/4 in, Shaft Type One End Threaded Shaft, End Type One End Threaded, Core Type Solid, Overall Length 13 in, Surface Hardness - Minimum 60 HRC, Material Carbon Steel, End Thread Size 1/2-13, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 0.749 in, Diameter Tolerance - Maximum 0.75 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable, End Thread Length 0.63 in

Linear Shaft, System of Measurement Inch, Diameter 3/4 in, Shaft Type One End Threaded Shaft, End Type One End Threaded, Core Type Solid, Overall Length 7 in, Surface Hardness - Minimum 60 HRC, Material Carbon Steel, End Thread Size 1/2-13, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 0.749 in, Diameter Tolerance - Maximum 0.75 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable, End Thread Length 0.63 in

Spline Shaft; Shaft Diameter 8 mm; Overall Length 150 mm; Material Stainless Steel; Minimum Surface Hardness 60 Rc; System of Measurement Metric; Diameter Tolerance Minimum 7.985 mm; Diameter Tolerance Maximum 8 mm; Finish Plain

Linear Shaft, System of Measurement Inch, Diameter 3/8 in, Shaft Type One End Threaded Shaft, End Type One End Threaded, Core Type Solid, Overall Length 8.5 in, Surface Hardness - Minimum 60 HRC, Material Carbon Steel, End Thread Size 1/4-20, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 0.374 in, Diameter Tolerance - Maximum 0.375 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable, End Thread Length 0.31 in

Linear Shaft, System of Measurement Inch, Diameter 3/4 in, Shaft Type Both Ends Threaded Shaft, End Type Both Ends Threaded, Core Type Solid, Overall Length 10 in, Surface Hardness - Minimum 60 HRC, Material Carbon Steel, End Thread Size 1/2-13, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 0.749 in, Diameter Tolerance - Maximum 0.75 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable, End Thread Length 0.63 in

Guide Rail, Overall Length 1,960 mm, Overall Width 15 mm, Overall Height 14 mm, Rail Material Aluminum, Manufacturer Size 15, Rail Type Profile, System of Measurement Metric, For Use With Alulin Carriages, Operating Temperature - Maximum 140 Degrees F, Operating Temperature - Minimum 32 Degrees F, Mounting Hole Center to Center 60 mm, Mounting Hole Center to Shaft End 28 mm, Channel Material Stainless Steel, Series Alulin, Mounting Hole Size 7.5 mm, Channel Type Not Applicable

Linear Shaft, System of Measurement Inch, Diameter 1/2 in, Shaft Type Both Ends Tapped Shaft, End Type Both Ends Tapped, Core Type Solid, Overall Length 6 in, Surface Hardness - Minimum 56 HRC, Material Stainless Steel, Finish Stainless Steel Coated, End Thread Size 1/4-20, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 0.499 in, Diameter Tolerance - Maximum 0.5 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable

Guide Rail, Overall Length 400 mm, Overall Width 25 mm, Overall Height 21.8 mm, Rail Material Aluminum, Manufacturer Size 25, Rail Type Profile, System of Measurement Metric, For Use With Alulin Carriages, Operating Temperature - Maximum 140 Degrees F, Operating Temperature - Minimum 32 Degrees F, Mounting Hole Center to Center 60 mm, Mounting Hole Center to Shaft End 28 mm, Channel Material Stainless Steel, Series Alulin, Mounting Hole Size 11 mm, Channel Type Not Applicable

Linear Shaft, System of Measurement Inch, Diameter 3/8 in, Shaft Type One End Tapped Shaft, End Type One End Tapped, Core Type Solid, Overall Length 12 in, Surface Hardness - Minimum 60 HRC, Material Carbon Steel, End Thread Size #8-32, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 0.374 in, Diameter Tolerance - Maximum 0.375 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable, End Thread Length 0.33 in

Linear Shaft, System of Measurement Inch, Diameter 5/8 in, Shaft Type Both Ends Tapped Shaft, End Type Both Ends Tapped, Core Type Solid, Overall Length 36 in, Surface Hardness - Minimum 60 HRC, Material Carbon Steel, End Thread Size 1/4-20, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 0.624 in, Diameter Tolerance - Maximum 0.625 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable, End Thread Length 0.5 in

Linear Round Flange Mount Bearing, Inside Diameter 3/4 in, Outside Diameter 1 1/4 in, Flange Width Not Applicable, Overall Length 1 5/8 in, Flange Diameter 2.188 in, Dynamic Load Capacity 862 N, Flange Thickness 0.313 in, Material Resin, Series SWF, Static Load Capacity 1,370 N, Steady State Speed 5 fps, Housing Style Single, System of Measurement Inch, Maximum Operating Temperature 176 Degrees F, Minimum Operating Temperature -4 Degrees F, Flange Shape Round, Finish Anodized

Guide Rail, Overall Length 640 mm, Overall Width 15 mm, Overall Height 14 mm, Rail Material Aluminum, Manufacturer Size 15, Rail Type Profile, System of Measurement Metric, For Use With Alulin Carriages, Operating Temperature - Maximum 140 Degrees F, Operating Temperature - Minimum 32 Degrees F, Mounting Hole Center to Center 60 mm, Mounting Hole Center to Shaft End 28 mm, Channel Material Stainless Steel, Series Alulin, Mounting Hole Size 7.5 mm, Channel Type Not Applicable

Linear Shaft, System of Measurement Inch, Diameter 5/8 in, Shaft Type Both Ends Tapped Shaft, End Type Both Ends Tapped, Core Type Solid, Overall Length 36 in, Surface Hardness - Minimum 56 HRC, Material Stainless Steel, Finish Stainless Steel Coated, End Thread Size 1/4-20, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 0.624 in, Diameter Tolerance - Maximum 0.625 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable

Spline Shaft, Shaft Diameter 10 mm, Overall Length 600 mm, Material Stainless Steel, Minimum Surface Hardness 60 Rc, System of Measurement Metric, Diameter Tolerance Minimum 9.985 mm, Diameter Tolerance Maximum 10 mm, Finish Plain

Linear Shaft, System of Measurement Inch, Diameter 1 1/4 in, Shaft Type Both Ends Tapped Shaft, End Type Both Ends Tapped, Core Type Solid, Overall Length 36 in, Surface Hardness - Minimum 56 HRC, Material Stainless Steel, Finish Stainless Steel Coated, End Thread Size 1/2-13, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 1.249 in, Diameter Tolerance - Maximum 1.25 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable

Linear Shaft, System of Measurement Inch, Diameter 1/4 in, Shaft Type One End Tapped Shaft, End Type One End Tapped, Core Type Solid, Overall Length 12 in, Surface Hardness - Minimum 60 HRC, Material Carbon Steel, End Thread Size #5-40, Mounting Hole Thread Size Not Applicable, Diameter Tolerance - Minimum 0.249 in, Diameter Tolerance - Maximum 0.25 in, Mounting Hole Center to Center Not Applicable, Mounting Hole Center to Shaft End Not Applicable, End Thread Length 0.25 in

Linear Square Flange Mount Bearing, Inside Diameter 1 1/2 in, Outside Diameter 2 3/8 in, Flange Width 3.75 in, Overall Length 5 11/16 in, Flange Diameter Not Applicable, Dynamic Load Capacity 3,420 N, Flange Thickness 0.5 in, Material Resin, Lubrication No Lubrication System, Series SWK-W, Static Load Capacity 8,040 N, Steady State Speed 5 fps, Housing Style Twin, System of Measurement Inch, Maximum Operating Temperature 176 Degrees F, Minimum Operating Temperature -4 Degrees F

Linear Shaft; System of Measurement Inch; Diameter 1 in; Shaft Type One End Tapped Shaft; End Type One End Tapped; Core Type Solid; Overall Length 12 in; Surface Hardness - Minimum 60 HRC; Material Carbon Steel; End Thread Size 3/8-16; Mounting Hole Thread Size Not Applicable; Diameter Tolerance - Minimum 0.999 in; Diameter Tolerance - Maximum 1 in; Mounting Hole Center to Center Not Applicable; Mounting Hole Center to Shaft End Not Applicable; End Thread Length 0.75 in

Linear Shaft; System of Measurement Inch; Diameter 1 in; Shaft Type One End Tapped Shaft; End Type One End Tapped; Core Type Solid; Overall Length 24 in; Surface Hardness - Minimum 60 HRC; Material Carbon Steel; End Thread Size 3/8-16; Mounting Hole Thread Size Not Applicable; Diameter Tolerance - Minimum 0.999 in; Diameter Tolerance - Maximum 1 in; Mounting Hole Center to Center Not Applicable; Mounting Hole Center to Shaft End Not Applicable; End Thread Length 0.75 in

Linear Shaft; System of Measurement Inch; Diameter 3/4 in; Shaft Type Both Ends Tapped Shaft; End Type Both Ends Tapped; Core Type Solid; Overall Length 24 in; Surface Hardness - Minimum 56 HRC; Material Stainless Steel; Finish Stainless Steel Coated; End Thread Size 5/16-18; Mounting Hole Thread Size Not Applicable; Diameter Tolerance - Minimum 0.749 in; Diameter Tolerance - Maximum 0.75 in; Mounting Hole Center to Center Not Applicable; Mounting Hole Center to Shaft End Not Applicable

Guide Rail; Overall Length 220 mm; Overall Width 25 mm; Overall Height 21.8 mm; Rail Material Aluminum; Manufacturer Size 25; Rail Type Profile; System of Measurement Metric; For Use With Alulin Carriages; Operating Temperature - Maximum 140 Degrees F; Operating Temperature - Minimum 32 Degrees F; Mounting Hole Center to Center 60 mm; Mounting Hole Center to Shaft End 28 mm; Channel Material Stainless Steel; Series Alulin; Mounting Hole Size 11 mm; Channel Type Not Applicable

Linear Shaft; System of Measurement Inch; Diameter 1/2 in; Shaft Type Both Ends Tapped Shaft; End Type Both Ends Tapped; Core Type Solid; Overall Length 24 in; Surface Hardness - Minimum 60 HRC; Material Carbon Steel; End Thread Size 1/4-20; Mounting Hole Thread Size Not Applicable; Diameter Tolerance - Minimum 0.499 in; Diameter Tolerance - Maximum 0.5 in; Mounting Hole Center to Center Not Applicable; Mounting Hole Center to Shaft End Not Applicable; End Thread Length 0.5 in

Linear Square Flange Mount Bearing; Inside Diameter 3/8 in; Outside Diameter 5/8 in; Flange Width 1.5 in; Overall Length 7/8 in; Flange Diameter Not Applicable; Dynamic Load Capacity 225 N; Flange Thickness 0.25 in; Material Resin; Lubrication No Lubrication System; Series SWK; Static Load Capacity 314 N; Steady State Speed 5 fps; Housing Style Single; System of Measurement Inch; Maximum Operating Temperature 176 Degrees F; Minimum Operating Temperature -4 Degrees F; Flange Shape Square

Linear Shaft; System of Measurement Inch; Diameter 1/4 in; Shaft Type One End Tapped Shaft; End Type One End Tapped; Core Type Solid; Overall Length 24 in; Surface Hardness - Minimum 60 HRC; Material Carbon Steel; End Thread Size #5-40; Mounting Hole Thread Size Not Applicable; Diameter Tolerance - Minimum 0.249 in; Diameter Tolerance - Maximum 0.25 in; Mounting Hole Center to Center Not Applicable; Mounting Hole Center to Shaft End Not Applicable; End Thread Length 0.25 in

Spline Shaft; Shaft Diameter 23 mm; Overall Length 950 mm; Material Stainless Steel; Minimum Surface Hardness 60 Rc; System of Measurement Metric; Diameter Tolerance Minimum 22.979 mm; Diameter Tolerance Maximum 23 mm; Finish Plain

Linear Shaft; System of Measurement Inch; Diameter 1 1/2 in; Shaft Type Both Ends Tapped Shaft; End Type Both Ends Tapped; Core Type Solid; Overall Length 36 in; Surface Hardness - Minimum 56 HRC; Material Stainless Steel; Finish Stainless Steel Coated; End Thread Size 5/8-11; Mounting Hole Thread Size Not Applicable; Diameter Tolerance - Minimum 1.499 in; Diameter Tolerance - Maximum 1.5 in; Mounting Hole Center to Center Not Applicable; Mounting Hole Center to Shaft End Not Applicable